Intel 810/815 Framebuffer driver¶
Tony Daplas <adaplas@pol.net>
March 17, 2002
First Released: July 2001 Last Update: September 12, 2005
A. Introduction¶
This is a framebuffer driver for various Intel 810/815 compatible graphics devices. These include:
Intel 810
Intel 810E
Intel 810-DC100
Intel 815 Internal graphics only, 100Mhz FSB
Intel 815 Internal graphics only
Intel 815 Internal graphics and AGP
B. Features¶
Choice of using Discrete Video Timings, VESA Generalized Timing Formula, or a framebuffer specific database to set the video mode
Supports a variable range of horizontal and vertical resolution and vertical refresh rates if the VESA Generalized Timing Formula is enabled.
Supports color depths of 8, 16, 24 and 32 bits per pixel
Supports pseudocolor, directcolor, or truecolor visuals
Full and optimized hardware acceleration at 8, 16 and 24 bpp
Robust video state save and restore
MTRR support
Utilizes user-entered monitor specifications to automatically calculate required video mode parameters.
Can concurrently run with xfree86 running with native i810 drivers
Hardware Cursor Support
Supports EDID probing either by DDC/I2C or through the BIOS
C. List of available options¶
- “video=i810fb”
enables the i810 driver
Recommendation: required
- “xres:<value>”
select horizontal resolution in pixels. (This parameter will be ignored if ‘mode_option’ is specified. See ‘o’ below).
Recommendation: user preference (default = 640)
- “yres:<value>”
select vertical resolution in scanlines. If Discrete Video Timings is enabled, this will be ignored and computed as 3*xres/4. (This parameter will be ignored if ‘mode_option’ is specified. See ‘o’ below)
Recommendation: user preference (default = 480)
- “vyres:<value>”
select virtual vertical resolution in scanlines. If (0) or none is specified, this will be computed against maximum available memory.
Recommendation: do not set (default = 480)
- “vram:<value>”
select amount of system RAM in MB to allocate for the video memory
Recommendation: 1 - 4 MB. (default = 4)
- “bpp:<value>”
select desired pixel depth
Recommendation: 8 (default = 8)
- “hsync1/hsync2:<value>”
select the minimum and maximum Horizontal Sync Frequency of the monitor in kHz. If using a fixed frequency monitor, hsync1 must be equal to hsync2. If EDID probing is successful, these will be ignored and values will be taken from the EDID block.
Recommendation: check monitor manual for correct values (default = 29/30)
- “vsync1/vsync2:<value>”
select the minimum and maximum Vertical Sync Frequency of the monitor in Hz. You can also use this option to lock your monitor’s refresh rate. If EDID probing is successful, these will be ignored and values will be taken from the EDID block.
Recommendation: check monitor manual for correct values (default = 60/60)
IMPORTANT: If you need to clamp your timings, try to give some leeway for computational errors (over/underflows). Example: if using vsync1/vsync2 = 60/60, make sure hsync1/hsync2 has at least a 1 unit difference, and vice versa.
- “voffset:<value>”
select at what offset in MB of the logical memory to allocate the framebuffer memory. The intent is to avoid the memory blocks used by standard graphics applications (XFree86). The default offset (16 MB for a 64 MB aperture, 8 MB for a 32 MB aperture) will avoid XFree86’s usage and allows up to 7 MB/15 MB of framebuffer memory. Depending on your usage, adjust the value up or down (0 for maximum usage, 31/63 MB for the least amount). Note, an arbitrary setting may conflict with XFree86.
Recommendation: do not set (default = 8 or 16 MB)
- “accel”
enable text acceleration. This can be enabled/reenabled anytime by using ‘fbset -accel true/false’.
Recommendation: enable (default = not set)
- “mtrr”
enable MTRR. This allows data transfers to the framebuffer memory to occur in bursts which can significantly increase performance. Not very helpful with the i810/i815 because of ‘shared memory’.
Recommendation: do not set (default = not set)
- “extvga”
if specified, secondary/external VGA output will always be enabled. Useful if the BIOS turns off the VGA port when no monitor is attached. The external VGA monitor can then be attached without rebooting.
Recommendation: do not set (default = not set)
- “sync”
Forces the hardware engine to do a “sync” or wait for the hardware to finish before starting another instruction. This will produce a more stable setup, but will be slower.
Recommendation: do not set (default = not set)
- “dcolor”
Use directcolor visual instead of truecolor for pixel depths greater than 8 bpp. Useful for color tuning, such as gamma control.
Recommendation: do not set (default = not set)
- <xres>x<yres>[-<bpp>][@<refresh>]
The driver will now accept specification of boot mode option. If this is specified, the options ‘xres’ and ‘yres’ will be ignored. See Documentation/fb/modedb.rst for usage.
D. Kernel booting¶
Separate each option/option-pair by commas (,) and the option from its value with a colon (:) as in the following:
video=i810fb:option1,option2:value2
Sample Usage¶
In /etc/lilo.conf, add the line:
append="video=i810fb:vram:2,xres:1024,yres:768,bpp:8,hsync1:30,hsync2:55, \
vsync1:50,vsync2:85,accel,mtrr"
This will initialize the framebuffer to 1024x768 at 8bpp. The framebuffer will use 2 MB of System RAM. MTRR support will be enabled. The refresh rate will be computed based on the hsync1/hsync2 and vsync1/vsync2 values.
- IMPORTANT:
You must include hsync1, hsync2, vsync1 and vsync2 to enable video modes better than 640x480 at 60Hz. HOWEVER, if your chipset/display combination supports I2C and has an EDID block, you can safely exclude hsync1, hsync2, vsync1 and vsync2 parameters. These parameters will be taken from the EDID block.
E. Module options¶
The module parameters are essentially similar to the kernel parameters. The main difference is that you need to include a Boolean value (1 for TRUE, and 0 for FALSE) for those options which don’t need a value.
Example, to enable MTRR, include “mtrr=1”.
Sample Usage¶
Using the same setup as described above, load the module like this:
modprobe i810fb vram=2 xres=1024 bpp=8 hsync1=30 hsync2=55 vsync1=50 \
vsync2=85 accel=1 mtrr=1
Or just add the following to a configuration file in /etc/modprobe.d/:
options i810fb vram=2 xres=1024 bpp=16 hsync1=30 hsync2=55 vsync1=50 \
vsync2=85 accel=1 mtrr=1
and just do a:
modprobe i810fb
F. Setup¶
Do your usual method of configuring the kernel
make menuconfig/xconfig/config
Under “Code maturity level options” enable “Prompt for development and/or incomplete code/drivers”.
Enable agpgart support for the Intel 810/815 on-board graphics. This is required. The option is under “Character Devices”.
Under “Graphics Support”, select “Intel 810/815” either statically or as a module. Choose “use VESA Generalized Timing Formula” if you need to maximize the capability of your display. To be on the safe side, you can leave this unselected.
If you want support for DDC/I2C probing (Plug and Play Displays), set ‘Enable DDC Support’ to ‘y’. To make this option appear, set ‘use VESA Generalized Timing Formula’ to ‘y’.
If you want a framebuffer console, enable it under “Console Drivers”.
Compile your kernel.
Load the driver as described in sections D and E.
Try the DirectFB (http://www.directfb.org) + the i810 gfxdriver patch to see the chipset in action (or inaction :-).
G. Acknowledgment:¶
Geert Uytterhoeven - his excellent howto and the virtual framebuffer driver code made this possible.
Jeff Hartmann for his agpgart code.
The X developers. Insights were provided just by reading the XFree86 source code.
Intel(c). For this value-oriented chipset driver and for providing documentation.
Matt Sottek. His inputs and ideas helped in making some optimizations possible.
H. Home Page:¶
A more complete, and probably updated information is provided at http://i810fb.sourceforge.net.
Tony